Something in the world of floating have you stumped?
Show Highlights
In this short, salty, and to the point episode, Graham and Ashkahn talk about installing float tanks on the second floor and how to work with contractors and engineers to determine if you need to reinforce your building to support the weight.
While you usually don’t need reinforcement, it’s always good to check. Listen in above or check out the transcript below and, as always, be sure to send us your questions. All questions welcome, from basic industry questions to well crafted stumpers. If Graham and Ashkahn don’t know the answer, they still relish the journey of discovery and educated guessing.
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Ashkahn: We’ve got a question today about being on the second floor of a building with your float center. So, if you’re thinking about putting a float center on the second floor, do you need to do any structural reinforcement to hold the weight of the float tank?
Graham: Let me just say definitively that, it totally depends.
Ashkahn: Yeah, that I think is a very concrete answer.
Graham: Of course, it’s going to depend on the building, how new your construction is, whether you’re in a big multi-story concrete kind of building or whether you’re in an old wooden Victorian house. There’s a lot that goes into it, but shockingly, the overall answer in almost all of those cases tends to be no. You don’t really need to do any extra reinforcement.
Ashkahn: Yeah, most times people bring in a structural engineer to take a look at things and examine it. Often landlords will even require you to do that.
Graham: Which you totally should do, don’t just listen to us and be like, “Oh it’s totally fine,” and go forward with it — a structural engineer is a great thing to bring in.
Ashkahn: It usually ends up being that while the float tank is heavy and all the salt water is heavy and all that, it’s just got such a big footprint. The float tanks are so big that the actual amount of pounds per square foot that’s really being put on, is not really as much as one might think. So it tends to be that a lot of buildings can hold it, even the way they are. Especially newer construction, like newer condo type buildings with strong reinforced concrete and stuff like that, tend to not really be much of a concern.
Graham: Again, surprisingly even for older buildings. Often times those are also good to go. Another good reason to consult an expert before spending a lot of money on reinforcements you might not necessarily need.
Ashkahn: Yeah, it’s always weird and there’s always weird stuff out there. I mean, even The Float Shoppe across the river from us, they’re in an old Victorian house and they brought a structural engineer in to check things out before they started and they found they could put float tanks on the second floor but their first floor was not actually strong enough to put float tanks on. Which is really crazy.
Graham: Yeah, so again, consult the experts and if it doesn’t work out, then you always can reinforce anyway.
Ashkahn: Boom.
Graham: Shakalaka.
Recent Podcast Episodes
What type of thermometer to use in a float tank – DSP 95
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
When should you call it quits? – DSP 94
Deciding when to close down is a challenge in any business, but it can hit especially hard for a float center. The upfront costs to build out are much higher than other industries, many of which simply cannot be recouped. When do you decide that it’s time to cut your losses and move on? What expenses can you recoup?
Graham and Ashkahn tackle this difficult question with laying out some sensible guidelines about what it means to run a business and how to go about it in a way that makes you comfortable.
Leaving a tank unattended for a week – DSP 93
Float tanks are like giant salty babies sometimes. Between water sanitation, temperature control, and filtration…they require a lot of attention and care, and even when you do things perfectly they can still make giant salty messes everywhere. So how do you leave your baby alone for a week? How do you prepare for that? Unlike a human baby, you can take your float tank with you (or at least it’s unlikely).
Choosing a Shower Disinfectant for your float center – DSP 92
A recommendation for a shower cleaner should be a fairly straightforward answer, right? Well… maybe not. Graham and Ashkahn are very particular about the definitions of things like “sanitation” “disinfectant” and other common cleaning terms. In this episode, they take the time to explain what product labels typically mean and what you want to look for when getting a surface cleaner for your float center.
Be ready to dive in and do some extra reading when getting into this episode. There’s a lot of terminology to parse and clarify. Fortunately, it’s Graham and Ashkahn so they have lots of really clear advice, like “don’t mix bleach and ammonia (or any homemade cleaning product, really)”.
When Does a Float Start? – DSP 91
Time management and maintaining your schedule is one of the most important quality controls in a float center. If you can’t get people out on time, it can throw off your schedule for the rest of the day. So, when does a float start? How do you measure that time? And what do you do if a floater starts late? Cut off their float? The next persons?
Graham and Ashkahn have been running Float On in a particular way for a long time now, and have particular insights into the challenges of how you manage your schedule.
Latest Blog Posts
No Results Found
The page you requested could not be found. Try refining your search, or use the navigation above to locate the post.
