Something in the world of floating have you stumped?
Show Highlights
Listen up future float center owners! Every one of you has probably wondered “What exactly does a transition look like in a float center from one float to the next?”
In this episode, Graham and Ashkahn explain exactly how they do transitions at Float On and why they do it the way they do.
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Ashkahn: Welcome to the podcast today. We have a fun question here. It is, “What are the things that need to take place during a transition?”
So, there’s five things that need to happen in a transition. Number one is running your filtration system. Plenty of stuff that we won’t go into at this point but that’s just one thing that has to happen. You gotta run your filtration system.
Number two is a visual check of the float tank. I think this is important every single time you do a transition. You gotta just look at the float tank. Look in the water. Make sure everything’s fine. Most of the time, the most common thing you’re gonna find is a neck pillow, right? Someone was in there. They had a neck pillow. They didn’t take it out when they left and you gotta get it out of there. Second most common thing I find is a rogue earplug. So, an earplug that came out of someone’s ear at some point in the float. We specifically get bright orange ear plugs so that they’re easy to spot during these visual inspections of the tanks during our transitions. The third most common thing is maybe like a hairball or something, you gotta kinda skim out of there, perhaps.
Graham: I was gonna say a crystal that someone left behind.
Ashkahn: A crystal that’s around? I think that’s like the fourth most common thing.
And then, you always want to check for worst case scenario sort of stuff, which is also probably something that we shouldn’t get into in the scope of this here. Always checking in case something catastrophic did go down and you need to deal with that.
Graham: AFRs. Look that up if you don’t know what that is.
Ashkahn: That’s step one and two. Run your filtration system. Two, visual inspection of the float tank.
Graham: Actually, if possible, do those in the reverse order, too. Like, ideally if you can, you’re doing the visual inspection of the float tank before you actually run your filtration system, so if there anything in there, it’s not getting sucked in.
Ashkahn: Yeah, ideally. I think lot of float centers in practice have trouble doing that just because they’re running their filtration systems maybe before people are coming out of the rooms. So, that’s definitely ideal, and sometimes not entirely possible for all float centers.
Graham: I’ll say feasible.
Ashkahn: Feasible.
Okay, the third thing is basically getting salt off of all the major salty spots, right? Anything anybody touches at any point inside the room is gonna have salt on it. Grab bars, light buttons, handles to your shower doors, your float tank, the lip of the float tank, the front part of the float tank under where people get out.
Graham: Every single thing in the room.
Ashkahn: Everything! Just everything is gonna have salt on it, and you gotta get that salt off. This step is where a lotta construction stuff comes in. There’s a lotta tricks you can do with how you build your room that makes this specific step as easy as possible, the biggest one being putting your showers as absolutely close to the doors of your float tanks as possible. Things like floor drains everywhere, proper slopes, color. The color you choose for things is really important for this. That kind of brushed nickel handlebar might be really nice and modern-looking, but you’re gonna want the white one, because that one’s gonna hide salt a lot better. So, as you’re wiping things off, if you miss a little nook and cranny somewhere, it’s okay. It’ll be really hard to spot. In general, the area that they’re touching is gonna be cleaned off, so colors, and kind of white, off white, colors with speckled bits of white mixed in to their patterns.
Graham: Mineral salt crystal designs on your walls.
Ashkahn: I did have someone suggest to me once, “Why not just build the room out of salt and that way, as people get it salty, it’ll just make the room stronger?”
Graham: I know. It sounds amazing. I don’t know the logistics of that, but it sounds amazing.
Ashkahn: So getting salt off of everything is another good step.
Graham: This is also where our pitch-black floors that had a gap of like three feet between our float tank and our shower with giant doors on our showers was really not a good idea.
Ashkahn: That was what we started as. We learned real fast. That was a big mistake.
So, getting salt off everything. The other step is sanitizing everything. You wanna go in and make sure that someone is not gonna spread disease to somebody else through being barefoot in the same place or having a skin rash and touching a handlebar or something like that. You can get whatever sanitizer you prefer. Most of the off the shelf items out there ranging from bleach to more industrial versions of Simple Green to various things like that are gonna have the capacity to sanitize between people and really, the important thing that I didn’t know before getting into the whole float tank world with all these different cleaning products you using is they all have kill times associated with them. If you just spray it on and wipe it off immediately and you don’t let it sit on the surface for the amount of time it’s supposed to sit there, you’re really not cleaning in the same way that you think you’re cleaning.
Basically, you can read the back of the bottle or sometimes it’s on the website for these different products. The EPA actually registers these products for different usages. You can actually go look up and they’ll say, After 30 seconds, it kills this list of things, and if you leave it on for a minute instead of 30 seconds, it’ll also kill this list of things, and if you leave it on for 10 minutes, then you start killing norovirus and certain fungi and stuff like that.
Look at that and make sure you’re doing it right. Often, the range you’re looking for is probably around a minute in terms of when you’re leaving it on there, so that’s something you gotta build into your transitions, too. You gotta spray down, and know that you’re leaving it there for a minute. Maybe you go do some other stuff before coming back and actually wiping it off.
Graham: You might be surprised once you actually look up those kill times how long some things take. Some things might have a 5 minute, or we’ve even seen things with a 10 minute kill time on certain items. A lot of times, if you’re not choosing the right kind of sanitizer for that, it can really cause issues.
Ashkahn: Yeah, some products, like the most basic version of Simple Green, I think, will never achieve certain kill rates even if you left it on for hours, as kind of even more industrial versions of Simple Green will in a minute. The Pro D5 is a slightly weaker version.
Graham: We call them Complicated Green.
Ashkahn: Yeah! Actually properly sanitizing things. You’re basically just trying to hit anything that someone is contacting, right? So the ground, the handlebars, the light button, stuff like that. Places that one person’s gonna touch that the next person’s also gonna touch.
And the last thing is replacing everything in the room that’s been used, like the towels, the robes, the earplugs, all of the stuff that we talked about before. You need to get all that stuff out and put new stuff in. We actually have a good method for trying to do that as fast as possible.
Graham: We do pretty much a full basket swap with all of the little things that go into a room, and grab the extras like the sandals and the neck pillow when we’re leaving, but essentially, we do a full room swap. Anything that was in the room for one person, we just switch it out, get it outta there, bring in the new, fresh batch, and that’s regardless of whether these things have been used or not, just because even if you’re trying to reuse the things that haven’t been used by the previous floater, the time to sort through those and figure out what’s been used and what hasn’t is not during this crazy transition crunch time, right?
The time to sort it out is when everyone’s in float tanks and you have a fair amount of time in between floats to actually take a look at the earplugs and figure out whether someone’s used them or not. Slowly over time, we’ve just found that the more that we can encourage that, the more we can make that an easy process, fully swapping out everything in the room, the quicker transitions go, and the more confident that we are that everything is actually being disinfected between every person, and we’re not ending up with something like earplugs where one of them was used and the other one wasn’t, and the person folded it and put it back in the little earplug container and placed it perfectly back in the basket, which has happened.
Or, people re-fold their towels exactly like they found them in the room despite the fact that the towels are now used and salty.
Ashkahn: Everybody’s gonna use a towel. I don’t think anyone made it out without using a towel before. Someone, I mean, you gotta use a towel at some point in the process.
Graham: So the point is, switching everything out. Don’t check it on the fly. That’s really the way that you want to make sure that everything in your room is being exchanged.
Ashkahn: It really is just that quality control you get from that. It’s really, really hard to train yourself to remember to check the sandals every single time if they only get used one out of every six floats or something like that. When they’re not happening that frequently, it’s a very, very difficult habit to build, and ultimately too difficult. We couldn’t get people to do it and people were ending up with salty stuff and things like that.
So, just swapping them out 100% of the time solves that problem and it’s faster and it’s better for sanitation. It means you can clean things properly. If you have sandals that people are using from one person to the next, you can let them sit with that sanitizer for 10 minutes and get to that full fungicidal kill time, and then wash it off and let it dry before putting it back into the room. It really kind of is a win across a lot of different variables.
Graham: How many things was that? Was that five?
Ashkahn: That was five. That was five. Visual check of the float tank, running your filtration system, wiping salt off of things, sanitizing things, and replacing things that were used in the room. Those are the things that you need to do. And then, I guess, giving people a walk-through if they’re new is five and a half. Not everybody needs that.
Graham: Alright. There you go. Transitions explained. Chicka-chicka-bow.
Recent Podcast Episodes
Tips for filling an empty service schedule – DSP 90
There are fewer things more stress inducing for a float center than seeing their schedule for the week and having it just be completely empty (Maybe watching your pump start up and spray water over your entire float room, but it’s a close call). What do you do in that situation? And how do you prevent it from happening in the future?
Well, Graham and Ashkahn have tried everything, from doing shout outs and deals on social media, to literally walking down the street trying to convince people to come in and float while the tanks were empty. Some tactics are more effective than others, but what it really comes down, at least in Float On’s case, is being prepared to give out a ton of free floats.
The guys talk about the effectiveness of each strategy they’ve tried and how they’ve reached out to contacts to form mutually beneficial business relationships and really get the ball rolling with filling up their tanks.
pH testing devices for float tank solution – DSP 89
There are lots of things you can measure when testing the quality of your water, for sanitation and comfort. Many of which aren’t specifically designed for float tanks. This is kind of an open secret in the industry, but most things simply aren’t accurate because of the incredibly high salinity of float tank solution. And pH seems to be one of them. This can cause float center owners major headaches as it’s often one of the first things that health departments/regulators will want to measure when they come and inspect your place (if they do at all).
Graham and Ashkahn try to break down this mystery of float water and try to break down some theories as to why it might be that float tank water might not have accurate pH readings, regardless of how you measure it.
Handling humidity to reduce water drops on tank ceilings – DSP 88
One of the biggest Float Mysteries in the industry is how to properly deal with condensation in a float tank. Your float tank is basically a giant humidity generating machine so clearly there’s going to be some condensation, but how much and why it forms can vary for seemingly no reason, making managing it difficult. The last thing any float center owner wants is for it to affect the floats they’re running (little water droplets falling on floaters is no fun).
Graham and Ashkahn commiserate with the industry about the difficulties in dealing with this particular hot topic, while also delving into the science of it and common solutions that should help any float center owner that’s facing this problem.
The purpose of a flow meters and the flow rate for a float tank – DSP 87
When navigating demands from health departments, it can be an absolute minefield of regulation, oftentimes with holdovers from the pool and spa industries. Many of these can be superfluous to float centers, but if you’re just starting a center, it’s difficult to know which ones to ignore, and which ones to incorporate.
Flow meters fall into this weird gray area where they’re not as important for float centers as for pools (and in some cases aren’t really needed at all), but can still be required by health departments or regulators. And to not throw the baby out with the salty bathwater, there are definitely some very practical uses for flow meters on float tanks.
Graham and Ashkahn tackle all these confusing elements and even provide specific product recommendations for flow meters for float tanks. Give it a listen!
When to contact health department – DSP 86
Contacting your health department/inspector/regulator/enforcer/supreme overlord can be stressful, to say the least. And given their general lack of understanding of floating as an industry, it makes sense why float centers may put this off. However, they have the authority to shut down your business if they feel that it’s a public safety issue, and that’s a situation no one should put themselves in.
Talking to your health department early and often can save yourself some headaches, but you don’t want to go to them unprepared. There’s a lot of nuance to regulation and existing codes that you should probably be familiar with beforehand. Fortunately, it may be something other float centers in your area have had to deal with, if there are any.
Ashkahn and Graham have a few tips for what to do to prepare and how to address common concerns they may have in this episode.
Latest Blog Posts
No Results Found
The page you requested could not be found. Try refining your search, or use the navigation above to locate the post.
