Something in the world of floating have you stumped?
Show Highlights
So HDPE stands for High Density Polyethylene. It’s a type of plastic and it’s incredibly handy for float centers. Float On switched to using this any place they previously would’ve used wood in their building materials.
Graham and Ashkahn break down exactly what this miracle product is, where you can buy it, all the different uses it has in a float center, and some special tips and tricks of getting it just the way you need it.
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: The question for today is, “What is HDPE and where the hell do you buy it?”
Ashkahn: Hmm.
Graham: Okay. Well, HDPE is high density polyethylene.
Ashkahn: Yep.
Graham: And you buy it at high density polyethylene stores.
Ashkahn: High Density Polyethylene Emporium.
Graham: Yeah. Basically it’s kind of like a plasticky plywood.
Ashkahn: Yeah, just plastic, yeah.
Graham: Almost is what, that’s, plywood, yeah.
Ashkahn: Plasticky plywood, I see what you’re saying there. I’m with you now.
Graham: And we use HDPE in a lot of areas where we would use wood.
Ashkahn: Yeah.
Graham: Because wood will get destroyed by all the moisture and salt and things like that. We want something that, of course, is just totally non-porous, and HDPE kind of fits the mold.
Ashkahn: Yeah a few float centers have a few wood things and buy special wood, and they put serious sealant on it and stuff like that. So I think there is a certain thing you can do to make wood work, but it’s easier just to buy plastic. It doesn’t quite look as nice, it looks like plastic.
Graham: I think it looks nice.
Ashkahn: It doesn’t look like a cheap little toy or something like that, it’s got some different finish to it that looks a little more matte or has a little bit of texturing and things like that.
Graham: For example, we kind of end up building these custom pump boxes around some of our pump filtration situations that we have going on. And we’ll end up building those out of HDPE for example, we’ll use HDPE as the platform to set our float tanks on with vibration isolation pads underneath.
Ashkahn: This is like, boats use this material to build their cabinets or parts of their outdoor things like doors, too. Different parts that are actually exposed to water. And basically the reason people like is it’s a plastic material, so it’s not gonna get damaged like wood or corroded like metal. But you can cut it, usually like with just a normal circular saw, like you’d be cutting wood. And you can screw into it like you would wood.
Graham: You can take it out to movies with you.
Ashkahn: Just like you would with a piece of 2×4.
Graham: Build yourself a little stand-up Ashkahn and Graham that you can keep with you at all times. Very flexible.
Ashkahn: You can manipulate it and you can work with it in the same way that you can with wood, but it’s made of plastic, and it’s strong and for a float center it’s water and salt resistant. And-
Graham: So, what were you gonna say?
Ashkahn: I was gonna say there’s certain versions, there’s brand names of HDPE out there that are a little bit more expensive and often it’s because they have some sort of UV resistant material mixed in to the HDPE, because again this is used a lot for boats and things like that.
Graham: SeaBoard, is that what it’s called?
Ashkahn: SeaBoard is one of the brands, I don’t know if there’s other brands, that’s definitely the one we know of.
Graham: Yeah. And they’ll just end up being more expensive. So the more generic HDPE, just because it’s gonna be used in float tank rooms, which are getting no exposure to sunlight at all, barely even exposure to fluorescent lights.
Ashkahn: So, yeah, you’re kind of just looking for generic HDPE boards. They come in all sorts of thicknesses and you can usually ask the company where you’re getting it from to cut it down to certain sizes for you. Because these things can be big, and they can be pretty heavy.
Graham: That gets to the second part of the question, which are what are these stores? Like big contractor plastics stores. Like heavy duty industrial supply, but for plastics, is often where you’ll pick this up.
Ashkahn: Yeah, like the places we found them are, you know, on the outskirts of town in the kind of area where you find all kinds of weird industrial stuff. And it’s just a company that deals in all sorts of different plastics is usually where we find it.
Graham: We were kind of joking at the beginning, but it is kind of a plastic emporium, is where you go to grab these things.
Ashkahn: I think I literally found ours just by Googling HDPE. Or another one is you can look at SeaBoard, and that’ll actually help you find specifically places that sell it, and then you can ask those people if they have generic HDPE as well.
Graham: Very clever.
Ashkahn: That’s actually how I remember finding the place we bought it for. The guy was like, “you don’t really need this SeaBoard stuff, why don’t you just get this other stuff we have, it’s the same thing without this UV stuff.” I was like okay cool, sounds great.
Graham: And for the record, do you remember what the thickness is that we use for the HDPE board when we’re usually getting it for under the tanks?
Ashkahn: For under the tank? I think we go with one inch.
Graham: I think so too, but now I’m thinking .75.
Ashkahn: It’s either .75 or an inch, but I’m leaning towards an inch. But I don’t know, somewhere in that range is probably okay.
Graham: We’ll call this off the record. Somewhere between three quarters and an inch is what we use under the tanks.
Ashkahn: But it’s heavy.
Graham: It’s really heavy.
Ashkahn: Like the nice thing is these come in a, well you can get plywood in bigger pieces than 4×8 as well, but same with HDPE, you can find it in larger pieces so you can actually use like a single piece underneath a float tank, but sometimes we cut them in two just for the ease of getting them into the room and not having it be like a huge gigantic single piece thing.
Graham: Also why it’s totally worth having the supplier actually cut it at their big warehouse, because it’s really hard stuff to move around in a big solid piece.
Ashkahn: The inch thick stuff is like, I mean it’s real heavy to lift the like 9×5 piece of one inch HDPE board. But once you get it there, it’s great. We’ve had it for some years now and like, it’s held up great. I haven’t noticed any damage or anything like that.
Graham: Oh yeah, not a problem with it at all. And little pro HDPE tip here, too. On the kind of sharp corners or edges of the HDPE you can actually sand that down like wood too. So really get rid of any kind of sharpness that you have when you’re putting it into your float rooms. Kind of like cut it at a curved angle and sand down the sharp little edges.
Ashkahn: Yeah, you can do anything. I make my clothes out of it. Protective. When I go clean the float tanks I’m totally covered.
Graham: It’s hard to get through the door, but. Alright. Anything else that you wanted to pass on about HDPE?
Ashkahn: I’ve never really looked into other, I don’t know if there’s like a low density polyethylene that would be like lighter, easy to work with. So I don’t know maybe someone can do more research.
Graham: High density monoethylene.
Ashkahn: This does seem to be a very generic, easy to come across thing. I guess it’s more expensive than wood, too, you should know that.
Graham: Oh, yeah.
Ashkahn: Like a big 4×8 sheet an inch thick was like two hundred something dollars if my memory is serving me correctly, something like that, maybe more?
Graham: It is more expensive, definitely. And we did used to have plywood in our rooms for the base of the tanks and stuff, and eventually we just had to replace it, so. The downside of going with something that isn’t impermeable is its life is ultimately limited.
Ashkahn: Yeah, for under the tank I would not use plywood.
Graham: No.
Ashkahn: It’s hard to get under there. We have ours set up to the point where, here’s another little tip for you guys here-
Graham: Just between you and us.
Ashkahn: Check this out. Here’s a little thing we got going on. We take our float tanks, we put them on an HDPE board, and the reason, I guess we should say the reason we’re even putting them on HDPE board in the first place is because we have all of our float tanks sitting on top of vibration isolation pads. We don’t want to connect the vibration isolation pads directly to the float tank unless your manufacturer says it’s okay, but we don’t want to connect them directly to the float tank because they’re just these little things. They’re like three inch by three inch pucks. So we’re worried that the strength of the fiberglass just sitting on those few small points will not be strong enough to have all of its weight distributed just over small-
Graham: Oh I’m convinced, I’m so certain that would cause problems.
Ashkahn: So instead what we do is we connect the three inch pucks, three inch by three inch pucks, to a piece of HDPE and then we set the whole float tank down on top of the HDPE board so then it goes basically float tank sitting on top of HDPE, sitting on top of usually 11 of these three inch by three inch vibration isolation pads. Kind of spread out in a pattern.
Graham: I just realized the acronym for that is VIPs by the way. Go on.
Ashkahn: The HDPE sitting on these VIPs, and the benefit of that, if you use HDPE and if you specifically use kind of water resistant anti mold mildew vibration isolation pads. Which, usually, most people use ones made by Diversitech. They use like EVA kind of material. The benefit at that point it that everything’s waterproof. And you can actually spray underneath your float tank.
Graham: Which is awesome.
Ashkahn: So instead of being worried about wood as salt just starts to get under there in these hard to reach places, or for whatever reason, you have something, a leak coming out of your filtration system and salt’s now underneath your float tank. When you have a system fully set up like this you can literally just take a sprayer or a hose or whatever and just spray underneath the float tank. If your slopes are set up well-
Graham: I was gonna say, if room is sloped properly then you have a drain possibly under there-
Ashkahn: Yeah, boom.
Graham: And a filtration that it’s running to.
Ashkahn: Now you’re talking. All that water just comes right back down, goes down a drain, that’s it. You’re living the good life. You can go sit back on your HDPE lounge chair and pull a martini out of your HDPE martini cup, and you know.
Graham: Pour some liquid HDPE in there and just go to town.
Ashkahn: Hang out. Relax. Its over. You’re done. Float tank takes care of itself at that point. So anyway I think that answers this question.
Graham: Yeah, if you have any more questions about fancy acronyms send them in to fts.com, that’s not it, it’s floattanksolutions.com/podcast
Recent Podcast Episodes
Should I Wire my Float Tanks into the Wall? – DSP 265
Ashkahn is currently recovering from his talk and the after-party last night, but Jake and Graham have gracefully taken the time to answer a construction question again today.
On the docket today is a question about wiring a float tank directly into the wall. Graham and Jake provide an overview of why some people may prefer this (it’s much easier to keep waterproof, e.g.), and why at Float On they use the twist lock for their outlets and how to properly utilize them.
Can I Keep My Old Ceiling With My Buildout? – DSP 264
Hopefully everyone had a lovely time at the Friday Activities and the after-party.
Ashkahn is still busy running the conference, but Graham and Jake have stepped in to talk about construction!
Today the guys talk about keeping a drop ceiling or T-bar ceiling in an existing space that you’re converting to a float center. The short answer is don’t keep it, as it can cause problems, but the guys do have some workarounds if your landlord is opposed to changing the ceiling.
What to Expect When Expanding from 1 to 3 Tanks? – DSP 263
Ashkahn is busy preparing for everything that happens tonight and tomorrow for the Conference, but that doesn’t mean Daily Solutions will stop being daily.
Graham and Jake talk construction and what to expect when you’re expecting… a giant expansion for your float center. What’s it look like when you go from one tank to three? How do the demands change? What needs to be put in place to make sure that you’re not hitting snags?
Fortunately, these guys know the score and are happy to share.
All About Floor Drains – DSP 262
As Ashkahn gets everything ready for the Start a Center Workshop (happening today) and the Float Conference this weekend, Graham and Jake tackle answering construction questions on the podcast.
Today they’re talking about floor drains. What to consider for drains and how they might pair with different types of flooring. Given the hefty price tag for these more advanced drains, having as much research before making a decision on these is essential. Luckily, the guys have done the hard part already and identified a lot of things to consider.
How to Deal with Float Room Humidity – DSP 261
Graham and Jake are at the helm again while Ashkahn puts the finishing touches on the Float Conference.
Today, the guys are talking all about humidity and how to deal with it when constructing your float rooms. They talk about all the little nuances that you (or your contractor) might not think about when it comes to humidity and how soundproofing and regular airflow may not always go hand in hand.
Latest Blog Posts
The Float Tour Blog – Issue #24
Alberta is often called the Texas of Canada. Part large oil industry, part cattle country.
Don’t Mess With Alberta!
At the base of the Rocky Mountains, replete with an Olympic Stadium, Calgary is a world-class destination for winter sports. The float community developed here similarly to Edmonton – there wasn’t anything nearby except for one or two residential float tanks, and then, in a short period of time, several centers opened all at once. Instead of competing, they’ve decided to work together and have developed one of the tightest knit float communities we’ve seen. They even have monthly Float Dinners, much like we do with the float centers in Portland. They don’t keep meeting minutes, so it’s hard to determine what they talk about at these dinners; my guess would be salt, the effects of salt on various substances, and how salty salt damage can make someone salty.
The Float Tour Blog – Issue #23
After Montana, we blazed our way back into Canada. The drive was long, but the scenery was beautiful. We followed the Rockies north, driving up to Edmonton. It’s a bit of a detour but, there are so many float centers in Edmonton, it seemed crazy not to stop by.
The city itself is primarily made up of workers from the oil fields – high risk, high income jobs that fuel the economy. At least until recently. Our visit was right in the middle of the Fort McMurray wildfire which has displaced a lot of the workforce, forcing 100,000 people to leave their homes. Many came to Edmonton, being the nearest metropolitan area to Fort McMurray. Some already split their time between the two cities, living in Edmonton and traveling to Fort McMurray for weeks or months at a time for work.
It’s understood that, in economic hardship, luxury commodities are typically the first thing people cut back on. Surprisingly, this doesn’t seem to be the case for floating. In fact, more people seem to be trying it to help alleviate the stress, many centers even offering free or discounted services to those displaced in an effort to help in a small way.
The Float Tour Blog – Issue #22
We’ve got two more stops in Colorado Springs before heading west. It’s a town known for its military base and long history of weapons testing. With such a large military presence, it comes as no surprise that the float center owners here are veterans, themselves.
After that, we shoot across to Salt Lake City. Utah is filled with gorgeous sights, from breathtaking lakes to stunning painted hills. With an international landmark famous for its effects on buoyancy, Salt Lake City should be pretty familiar with the concept of floating. With five different float centers, and the manufacturer of the Zen Tent out there, there could be some cause and effect.
After that, we head up into Idaho and Montana to close out the Central United States portion of our Tour. We’ll follow the Rocky Mountains north, taking in the scenery along the way.
The Float Tour Blog – Issue #21
Denver has been home to a vibrant float community for a long time. Some of the earliest commercial centers that started up in the ‘70s and ‘80s were out here. 30 years is a long time, and most of the old centers aren’t around anymore, but there’s a conscious community that has been floating since the old days and they love how much the industry has evolved and grown.
